4K60 Edge Blending Video Wall Processor

The Avenview MLT-EDGEPRO-2X2E is a next generation dual output multi format input professional curved screen and edge blending processor. It was designed for advanced edge blending as well as image warping, stacking, projection mapping, irregular video wall, passive 3D and much more. The edge blending processor has 4 inputs (2x HDMI, 1xDP, 1xVGA) and 2x HDMI outputs integrated in MLT-EDGEPRO-2X2E. Input ports support up to 4096*2160 @60Hz with 4:4:4 full color sampling. Output supports up to 2048*1080 @60Hz. It is integrated with 10-bit processor, motion adaptive de-interlace, low angle smooth algorithm, 3:2/2:2 pull-down and supports programmable EDID, non-VESA standard input timing, Advanced and warp technology is embedded in the EdgePro. This Processor is Equipped with an IR controller to perform edge blending and sophisticated geometry alignment up to 9×5 grids through remote controller and 17×17 grids from WebGui, PC tool via USB or Ethernet. The EdgePro features an advanced Linear Grid Adjustment and Corner Wall image adjustment for mapping of 90 degrees corners. This unit boasts Independent RGB gamma correction for edge blending region, color fine-tune and individual color correction for each output, fine pixel color uniformity and 9 regions non-edge blending area black level uplift. With real time geometry and colour adjustment the most optimized results can be achieved. An HDMI loop out supports daisy chain connection with up to 4096×2160 @60Hz and allows large display with multiple EdgePro cascaded. The Video wall function in EdgePro crops and allocate source image for each projector setting overlap pixels for edge blending. Complete control can be achieved via Ethernet without PC software. With the MLT-EDGEPRO-2X2E, users can replace high end projectors with low cost projectors without lens shift, warp and edge blending features. It provides easy configuration, lower cost, reliable and flexible solution.

Features

Input ports: 2x HDMI, 1xVGA, 1x DisplayPort

• HDMI & DisplayPort support 4096*2160 @60Hz, 3840*2400 @60Hz with 4:4:4 sampling without compression. VGA supports up to WUXGA or 205MHz analog input signal.
• Connect with various video sources and support none VESA standard input resolution.

Output ports: 2x HDMI.

• Selectable output resolutions: 720×480, XGA, WXGA, 1280×1024,1366×768, 1400×1050, 1600×1200, 1920×1080 (24/30/50/60Hz), 2048×1080/60 &1920*1200/60.

Loop out port: 1x HDMI

• Signal frame lock for synchronization between multiple output channels. (supports 4096*2160@60Hz & 3840×2400@60Hz)

Image warp, geometry alignment and edge blending

• Selectable grid pattern size for geometry alignment from 8-100 pixels in H&V with variable color and styles. Default size is 32*32 pixels.
• With full functions for quick 4 corner alignment, vertical and horizontal keystone correction, Pincushion & Barrel adjustment, image warp and image 90/180/270 degrees rotation and flip.
• Each unit controls dual projectors and can be cascaded to control unlimited number of projectors.
• Integrated with full function IR remote controller. Manual geometry alignment up to 9*5 grid patterns with H=+_ 1200 pixels and V=+_1200 adjustment range in full HD output (4 corner +warp adjustment).
• Windows PC tool is available for warp and geometry alignment up to 17×17 grid patterns with H=+_1200 pixels and V=+_1200 pixels adjustment range in full HD output through USB or Ethernet. After finishing geometry alignment, the parameters can be stored inside EdgePro and no more PC tool is needed.
• Corner wall geometry alignment at 90 degrees corner wall up to 900 pixels adjustment range in H&V directions with up to 1200 pixels position adjustment in horizontal direction.
• Four directions edge blending up to H=1920, V=1200 overlapped pixels for flat, curved &cylindrical screens.
• Independent RGB gamma selection for edge blending color fine tune.
• Precise black level uplift at multiple selected areas (up to 9) to compensate light leakage in the projector.
• White balance and individual color correction for each projector.
• 1Fine pixel color uniformity adjustment across entire image.

High end 10-bit video processor

• Integrated with 10-bit high end processor with 3D motion adaptive de-interlace, low angle smooth algorithm and 3:2/2:2 film mode detect and recovery function.
• Complete color adjustment function, including brightness, contrast, hue, saturation, pre-set color temperature, independent RGB color adjustment and white balance correction.

Edge mask

• Image [SHIFT] to execute edge mask up to 500 pixels following the image after geometry adjustment and Edge [Mask] with 8 adjustment points to provide irregular edge mask up to 900 pixels in each control point.

Video wall function

• Image cropping and location assignment for each projector.
• Overlap pixel adjustments up to 1800 pixels for image position shift, bezel compensation and creating overlap region for edge blending and aspect ratio adjustment.
• Connect with 4k/2k input signal and split the image for display devices without additional PC, image splitter or other devices.
• Serve as video wall controller for irregular video wall display up to 15×15 matrix display from single signal input source.

Image rotation and flip

• Image 90/270 degrees’ rotation & flip under 4k/30Hz input. Image 0/180 degrees’ rotation and flip supports up to 4k/60Hz input.

System control and other features

• 1U housing for easy rack installation. Professional design and reliable.
• Replace high price projector with low cost projector and achieve the same functionality.
• Full function OSD by IR remote controller.
• Full function system setup through USB, WebGUI via Ethernet or Wi-Fi  on PC, Mobile or iPad
• Firmware update via USB or Ethernet.
• Windows PC tool can control multiple processors simultaneously through USB or Ethernet.
• Internal grid pattern with selective pixel size, color and style for easy geometry alignment.
• RS232 & Ethernet system control compatible with most of control system.
• User can select blue or black background color when no input signal is detected.
• Programmable EDID in the range at H=1024~3840, V=720~2400.
• BOX ID and programmable IP address for convenient multiple unit control at the same time.
• User can save up to 5 settings and can be recalled by remote controller, RS232, USB or network.
• Automatic power ON/OFF through input signal control. While no input signal is detected, it will shut down output automatically.

Specifications

ITEM	DESCRIPTION
UNIT	MLT-EDGEPRO-2X2E
UNIT DESCRIPTION	4K Edge blending Video wall processor
INPUT PORTS	2x HDMI 2.0b 1x DP1.2a 1x VGA
OUTPUT PORTS	2x HDMI up to 2048×1080/60 & WUXGA
OUTPUT RESOLUTION	2x HDMI up to 1920×1200@60, 1x HDMI Loop out up to 3840×2160@30
INPUT RESOLUTION	720×480, XGA, WXGA, 1280×1024, 1366×768, 1400×1050, 1600×1200, 1920×1080 (24/30/50/60Hz), 2048×1080/60 & 1920*1200/60.
HDCP VIDEO COMPLIANCE	HDMI V2.2/V1.4, DP: HDCP: V1.3
CASCADABLE	Yes
DIGITAL AUDIO SUPPORT	Embedded HDMI & SPDIF audio outputs
VIDEO LOOP OUT	Yes
PRESET PROFILES	Up to 5 preset output modes
BEZEL COMPENSATION	Yes. (in video wall mode)
CONTROL	IR, RS232, USB, Ethernet
DIMENSIONS (L X W X H)	17.3” x 7.4” x 1.8”
POWER SUPPLY	110-240V
POWER CONSUMPTION	Max. 11w
LED	Front Panel Indicator
WEIGHT	5.18 lbs
ENVIRONMENTAL
OPERATING TEMPERATURE	32° ~ 104°F (0° to 40°C)
STORAGE TEMPERATURE	-4° ~ 140°F (-20° ~ 60°C)
ESD PROTECTION	Human body model — ±8kV (air-gap discharge) & ±4kV (contact discharge)
RELATIVE HUMIDITY	20~90% RH (no condensation)

Diagram

Product Video

Software

•  Avenview DVI-SPLITPRO-2X Advanced Dual Screen Multiviewer Control Software

Additional Guides

• Avenview DVI-SPLITPRO-2X IP Guide